1. General description
The NE1617A is an accurate two-channel temperature monitor. It measures the
temperature of itself and the temperature of a remote sensor. The remote sensor is a
diode connected transistor. This can be in the form of either a discrete NPN/PNP, such as
the 2N3904/2N3906, or a diode connected PNP built into another die, such as is done on
some Intel microprocessors.
The temperature of both the remote and local sensors is stored in a register that can be
read via a 2-wire SMBus. The temperatures are updated at a rate that is programmable
via the SMBus (the average supply current is dependent upon the update rate the
faster the rate, the higher the current).
In addition to the normal operation, which is to update the temperature at the programmed
rate, there is a one-shot mode that will force a temperature update.
There is also an alarm that senses either an overtemperature or undertemperature
condition. The trip points for this alarm are also programmable.
The device can have one of nine addresses (determined by two address pins), so there
can be up to nine of the NE1617A on the SMBus.
It can also be put in standby mode (in order to save power). This can be done either with
software (over the SMBus) or with hardware (using the STBY
pin).
2. Features and benefits
n Replacement for Maxim MAX1617 and Analog Devices ADM1021
n Monitors local and remote temperature
n Local (on-chip) sensor accuracy:
u ?/SPAN>2 ?/SPAN>C at 60 ?/SPAN>C to 100 ?/SPAN>C
u ?/SPAN>3 ?/SPAN>C at -40 ?/SPAN>C to 125 ?/SPAN>C
n Remote sensor accuracy:
u ?/SPAN>3 ?/SPAN>C at 60 ?/SPAN>C to 100 ?/SPAN>C
u ?/SPAN>5 ?/SPAN>C at -40 ?/SPAN>C to 125 ?/SPAN>C
n No calibration required
n Programmable overtemperature/undertemperature alarm
n SMBus 2-wire serial interface up to 100 kHz
n 3 V to 5.5 V supply range; 5.5 V tolerant
n 70 mA supply current in operating mode
n 3 mA (typical) supply current in standby mode
NE1617A
Temperature monitor for microprocessor systems
Rev. 5 20 March 2012
Product data sheet
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
NE1619DS,118
IC TEMP MONITOR 16SSOP
NIS5112D1R2G
IC ELECTRONIC FUSE HOTSWAP 8SOIC
NIS5132MN2TXG
IC ELECTRONIC FUSE 12V 10DFN
NIS5132MN3TXG
IC ELECTRONIC FUSE 12V 10-DFN
NSI45015WT1G
IC LED DRIVER LINEAR SOD-123
NSI45020AT1G
IC LED DRIVER LINEAR SOD-123
NSI45020JZT1G
IC LED DRVR CONST CURRENT SOT223
NSI45020T1G
IC CCR/LED DVR 45V 20MA SOD-123
相关代理商/技术参数
NE1617ADS,118
功能描述:板上安装温度传感器 TEMP SENSOR DIGITAL RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
NE1617ADS/G,118
制造商:NXP Semiconductors 功能描述:Tape & Reel
NE1617DS
功能描述:板上安装温度传感器 I2C LOC +/- 2OC AND REM +/- 3OC TS RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
NE1617DS,112
功能描述:板上安装温度传感器 I2C LOC +/- 2OC AND RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
NE1617DS,118
功能描述:板上安装温度传感器 I2C LOC +/- 2OC AND REM +/- 3OC TS RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
NE1618
制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Temperature monitor for microprocessor systems
NE1618DS
制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Temperature monitor for microprocessor systems
NE1618DS,112
功能描述:板上安装温度传感器 PRECISION TEMPERATURE MONITOR RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor